Grain-systems PNEG-1283 Manual de usuario

PNEG-1283Moisture SamplerInstallation ManualPNEG-1283Date: 10-09-09

4. Installation10 PNEG-1283 Moisture Sampler12. Install Moisture Sampler discharge cover (D01-2305-8) in top two (2) holes drilled in the box end usin

4. InstallationPNEG-1283 Moisture Sampler 11Figure 4G 18. Install sheave (018-1047-2) and bushing (D32-0016) on the bottom auger shaft that extends th

4. Installation12 PNEG-1283 Moisture Sampler19. To install the Moisture Sampler drive belt, loop the belt over one of the sheaves and the stretch it o

4. InstallationPNEG-1283 Moisture Sampler 13Installation Instructions for Dryers with New Discharge Box AssemblyFigure 4K 1. Remove the Moisture Sampl

4. Installation14 PNEG-1283 Moisture SamplerFigure 4L 4. Complete Steps 18-20 starting on Page 11.Sensor end 4 ea. 5/16"-18 x 1-1/4" bolt (S

PNEG-1283 Moisture Sampler 15NOTES

16 PNEG-1283 Moisture Sampler5. Parts ListMoisture Sampler91113124

5. Parts ListPNEG-1283 Moisture Sampler 17Moisture Sampler Parts ListRef # Part # Description Qty1 017-1451-8 Sheave, AK46H 4.2 PD 12 D03-0845 Bearing

18 PNEG-1283 Moisture Sampler6. Assembly InstructionsMoisture Sampler Assembly (D04-0550)NOTE: 1. DC-1944 to be placed on top of D01-1944-8.2. D01-188

6. Assembly InstructionsPNEG-1283 Moisture Sampler 19Moisture Sampler Assembly (D04-0550) (Continued)Ref # Part # Description Qty1 D01-1944-8 Moisture

2 PNEG-1283 Moisture Sampler

6. Assembly Instructions20 PNEG-1283 Moisture SamplerMoisture Sampler Update Kit (D04-0532) Assembly InstructionsTo replace parts used on the D01-1945

PNEG-1283 Moisture Sampler 217. WarrantyGSI Group, LLC Limited WarrantyThe GSI Group, LLC (“GSI”) warrants products which it manufactures to be free o

This equipment shall be installed in accordance with the current installation codes and applicable regulations which should be carefully followed in a

Table of ContentsPNEG-1283 Moisture Sampler 3ContentsChapter 1 Safety ...

4 PNEG-1283 Moisture Sampler2. SafetySafety GuidelinesThis manual contains information that is important for you, the owner/operator, to know and unde

2. SafetyPNEG-1283 Moisture Sampler 5Safety InstructionsOur foremost concern is your safety and the safety of others associated with this equipment. W

6 PNEG-1283 Moisture Sampler3. DecalsIf the decal used for this installation is damaged or is missing contact:GSI Decals1004 E. Illinois St.Assumption

PNEG-1283 Moisture Sampler 74. InstallationInstallation Instructions for Dryers Made before September 2002Figure 4A 1. Remove the auger bearing shield

4. Installation8 PNEG-1283 Moisture Sampler3. Disconnect the tilt switch and remove conduit from the discharge box. (See Figure 4C.)Figure 4C 4. Remov

4. InstallationPNEG-1283 Moisture Sampler 910. Now put the Moisture Sampler assembly up to the discharge box again and put in the 5/16" bolts and